TA-50/BS-50 : Triax Cable Extension System

• 
• 
• 

• 
• 
• 

 

TA-50/BS-50 is Ikegami’s latest SDTV triax cable extension system that delivers long and wideband (6MHz) RGB transmission over a maximum of 1500m (Fujikura ¢14.5mm), without compromising high picture quality captured by a camera.　The system comes standard with two SDI component serial digital outputs to support digital broadcasting at high levels of sophistication, while retaining compatibility with Ikegami’s high-grade and high end SDTV camera HL-65W and HK-399PW. This newest triax cable extension system offers excellent performance not only in field, but also in studio, satisfying the whole gamut of needs, from news gathering to production, with the best quality possible.

• Features
• Ratings
• Request

QTV Video(AUX) signal is available by installation of optional Q-TV demand module. (TA-50)

ID code with 4 bit can be provided to camera through 200 pin I/F connector. (TA-50)

Large viewfinder of 5-inch can be used without external power supply by enough power capacity. (TA-50)

Q-TV input as standard. (BS-50)

Compact base station with 1U Full-rack size. (BS-50)

The name of the camera type can be indicated on the LCD displayon the front panel. (BS-50)

RET video input (2ch) can be remotely controlled from camera head. (BS-50)

R/G/B/Y/ENC can be selected from OCP/MCP for MON out.

[TA-50] Specification
Input Signals
MIC-1/2 Signals	-60 ~ -40/-20 dBs600 ohm balance (12V/48V Phantom power : only MIC-2)
INCOME ENG Signal	Dynamic Headset-60dBs (Dynamic Mic) High imp Carbon/Dynamic with AMP Headset (Power will be supplied from TA) -16dBs (Carbon Mic) High imp
INCOME PRD Signal	Dynamic Headset-60dBs (Dynamic Mic) High imp Carbon/Dynamic with AMP Headset(Power will be supplied from TA) -16dBs (Carbon Mic) High imp
Data Signal (RX Data)	Separate RS232C link (p+tetc)
EXT	DC IN 10.5 ~ 13.5V
Output Signals
RET Video Signal	VBS 1Vp-p Positive polarity 75 Ohm
INCOM ENG Signal (Headset)	+10dBs Low imp Output
INCOM PRD Signal (Headset)	+10dBs Low imp Output
PGM-1 Signal (INCOM MIX)	+10dBs low imp Output
PGM-2 Signal ((NCOM IX)	0 dBslow imp Output Q-TV Video Signal Cable length Max:500m(fujikura ¢8.8mm)VBS 1Vp-p Positive polarity 75 Ohm
Data Signal (TX Data)	Separate RS232C link (p+tetc) *9600 bps max
DC12V OUT	Max 1.5A for 6inch VF *Internal power only Max 2.0A for Box type Lenses *Internal power only *100 of 12V power available at TAMax 0.5A for (Wireless Receiver)
[BS-50] Specification
Input Signals
External Sync Signal	BBS 0.45Vp-p Positive polarity 75ohm Bridge possible
RET-2 Video Signal	VS/VBS 1Vp-p Positive polarity 75ohm Bridge possible
Q-TV Video Signal	VS/VBS 1Vp-p Positive polarity 75ohm Bridge possible
PGM Audio Signal	0dBm/-20dBm 600 Ohm/10K Ohm Balance w/o Transformar
Intercom (ENG) Signal (INTERCOM CN:switchable)	(1)4-wires0dBs 10K Ohm/600 Ohm Balance w/o Transformer (2) RTS1Vp-p High imp (3) Clearcom-15 dBsHigh imp
Intercom Signal (Main INCOM Jack)---ENG	(1) Carbon/Dynamic Head Set with AMP ---Power will be supplied -16dBs (2) Dynamic Head Set-60dBs (3) Type of connectorUser-Choice XLR-5 or equivalent as standard Ikegami MCP COMMAND Signal (HEC) Ikegami OCP COMMAND Signal (HEC)
Data Signal (RX Data)	Separate RS232C link (p+tetc) 9600bps
Output Signals
ENC-1 Analog Video Signal	VBS 1Vp-p Positive polarity 75 Ohm
ENC-2 Analog Video Signal	VBS 1Vp-p Positive polarity 75 Ohm
SDI-1 Component Serial Digital Signal	270 Mbps 0.8Vp-p 75 Ohm
SDI-2 Component Serial Digital Signal	270 Mbps 0.8Vp-p 75 Ohm
Component Analog Video Signal	(1) Y (Luminance Signal)1Vp-p Positive polarity 75 Ohm (2) Cb, Cr Chromasignal)0.525Vp-p 75 Ohm
R,G and B Analog Video Signals	(1) R Video V 0.7Vp-p Positive polarity 75 Ohm (2) G VideoV 0.7Vp-p Positive polarity 75 Ohm (3) B VideoV 0.7Vp-p Positive polarity 75 Ohm
Monitor Video Signals	VS/VBS 1Vp-p Positive polarity 75 Ohm
SYNC Signal	SYNC 1Vp-p Negative polarity 75 Ohm
MIC-1 Audio Signal	0 dBm 600Ohm Balance Output
MIC-2 Audio Signal	0 dBm 600Ohm Balance Output
INCOM ENG Signals	(1)4-wires 0dBm600 Ohm Balance Output w/o Transformer (2)RTS1 Vp-p200 Ohm (3)Clearcom1 Vp-p200 Ohm
INCOM PRD Signals	(1) 4-wires0 dBm600 Ohm Balance Output w/o Transformer (2) RTS1 Vp-p200 Ohm (3) Clearcom1 Vp-p200 Ohm
INCOM Signals (Main INCOM JACK)---ENG	Head Set OutputLow impedance +10dB at maximum control
TALLY (R,G) Signals (for picture monitor)	Contact closure
Ikegami OCP COMMAND Signal (HED)
Ikegami MCP COMMAND Signal (HED)
Data Signal (TX Data)	Separate RS232C link (p+tetc) 9600bps
Transmission Distance	Triax Cable75m to 750m with φ8.8mm Fujikura 150m to 1500m with φ14.5mm Fujikura
Power Requirement	AC Input voltageAC100-120V/220-240V +/-10% 50/60Hz Power consumptionLess than 86VA (with Cam,smallVF,smallLens) Transmission Power Supply VoltageDC270V
Ambient Temperature	Triax Camera Adaptor:-20°C ~ +45°C, Base Station:20°C ~ +45°C
Ambient Humidity	Triax Camera Adaptor:-25% ~ +85%, Base Station:25% ~ 85%
Weight	Triax Camera Adaptor: Approx. 2kg, Base Station:Approx. 6.3kg

---

• In case of emergency, please fill it in the message field.
• This page is encrypted using SSL before transmission.
• Ikegami shall properly handle personal information in accordance with the privacy policy posted on our website.
• For additional information shall refer to "Privacy Statements" on our website.
• Please fill-out all fields for sign up, click "Confirm" button.
• Preffered to fill in English.
• In case, if you are accessing from European Union (EU) countries, please use Ikegami Europe official site, contact form to comply with the EU General Data Protection Regulation (GDPR). [Contact form: http://www.ikegami.de/contact.html]

Ikegami Electronics Asia Pacific Pte. Ltd.