TA-50/BS-50
Triax Cable Extension System
Discontinued Product
TA-50/BS-50 is Ikegami’s latest SDTV triax cable extension system that delivers long and wideband (6MHz) RGB transmission over a maximum of 1500m (Fujikura ¢14.5mm), without compromising high picture quality captured by a camera. The system comes standard with two SDI component serial digital outputs to support digital broadcasting at high levels of sophistication, while retaining compatibility with Ikegami’s high-grade and high end SDTV camera HL-65W and HK-399PW. This newest triax cable extension system offers excellent performance not only in field, but also in studio, satisfying the whole gamut of needs, from news gathering to production, with the best quality possible.
QTV Video(AUX) signal is available by installation of optional Q-TV demand module. (TA-50)
ID code with 4 bit can be provided to camera through 200 pin I/F connector. (TA-50)
Large viewfinder of 5-inch can be used without external power supply by enough power capacity. (TA-50)
Q-TV input as standard. (BS-50)
Compact base station with 1U Full-rack size. (BS-50)
The name of the camera type can be indicated on the LCD displayon the front panel. (BS-50)
RET video input (2ch) can be remotely controlled from camera head. (BS-50)
R/G/B/Y/ENC can be selected from OCP/MCP for MON out.
| [TA-50] Specification | |
| Input Signals | |
| MIC-1/2 Signals | -60 ~ -40/-20 dBs600 ohm balance (12V/48V Phantom power : only MIC-2) |
| INCOME ENG Signal | Dynamic Headset-60dBs (Dynamic Mic) High imp Carbon/Dynamic with AMP Headset (Power will be supplied from TA) -16dBs (Carbon Mic) High imp |
| INCOME PRD Signal | Dynamic Headset-60dBs (Dynamic Mic) High imp Carbon/Dynamic with AMP Headset(Power will be supplied from TA) -16dBs (Carbon Mic) High imp |
| Data Signal (RX Data) | Separate RS232C link (p+tetc) |
| EXT | DC IN 10.5 ~ 13.5V |
| Output Signals | |
| RET Video Signal | VBS 1Vp-p Positive polarity 75 Ohm |
| INCOM ENG Signal (Headset) | +10dBs Low imp Output |
| INCOM PRD Signal (Headset) | +10dBs Low imp Output |
| PGM-1 Signal (INCOM MIX) | +10dBs low imp Output |
| PGM-2 Signal ((NCOM IX) | 0 dBslow imp Output Q-TV Video Signal Cable length Max:500m(fujikura ¢8.8mm)VBS 1Vp-p Positive polarity 75 Ohm |
| Data Signal (TX Data) | Separate RS232C link (p+tetc) *9600 bps max |
| DC12V OUT | Max 1.5A for 6inch VF *Internal power only Max 2.0A for Box type Lenses *Internal power only *100 of 12V power available at TAMax 0.5A for (Wireless Receiver) |
| [BS-50] Specification | |
| Input Signals | |
| External Sync Signal | BBS 0.45Vp-p Positive polarity 75ohm Bridge possible |
| RET-2 Video Signal | VS/VBS 1Vp-p Positive polarity 75ohm Bridge possible |
| Q-TV Video Signal | VS/VBS 1Vp-p Positive polarity 75ohm Bridge possible |
| PGM Audio Signal | 0dBm/-20dBm 600 Ohm/10K Ohm Balance w/o Transformar |
| Intercom (ENG) Signal (INTERCOM CN:switchable) | (1)4-wires0dBs 10K Ohm/600 Ohm Balance w/o Transformer (2) RTS1Vp-p High imp (3) Clearcom-15 dBsHigh imp |
| Intercom Signal (Main INCOM Jack)---ENG |
(1) Carbon/Dynamic Head Set with AMP ---Power will be supplied -16dBs |
| Data Signal (RX Data) | Separate RS232C link (p+tetc) 9600bps |
| Output Signals | |
| ENC-1 Analog Video Signal | VBS 1Vp-p Positive polarity 75 Ohm |
| ENC-2 Analog Video Signal | VBS 1Vp-p Positive polarity 75 Ohm |
| SDI-1 Component Serial Digital Signal | 270 Mbps 0.8Vp-p 75 Ohm |
| SDI-2 Component Serial Digital Signal | 270 Mbps 0.8Vp-p 75 Ohm |
| Component Analog Video Signal | (1) Y (Luminance Signal)1Vp-p Positive polarity 75 Ohm (2) Cb, Cr Chromasignal)0.525Vp-p 75 Ohm |
| R,G and B Analog Video Signals | (1) R Video V 0.7Vp-p Positive polarity 75 Ohm (2) G VideoV 0.7Vp-p Positive polarity 75 Ohm (3) B VideoV 0.7Vp-p Positive polarity 75 Ohm |
| Monitor Video Signals | VS/VBS 1Vp-p Positive polarity 75 Ohm |
| SYNC Signal | SYNC 1Vp-p Negative polarity 75 Ohm |
| MIC-1 Audio Signal | 0 dBm 600Ohm Balance Output |
| MIC-2 Audio Signal | 0 dBm 600Ohm Balance Output |
| INCOM ENG Signals | (1)4-wires 0dBm600 Ohm Balance Output w/o Transformer (2)RTS1 Vp-p200 Ohm (3)Clearcom1 Vp-p200 Ohm |
| INCOM PRD Signals | (1) 4-wires0 dBm600 Ohm Balance Output w/o Transformer (2) RTS1 Vp-p200 Ohm (3) Clearcom1 Vp-p200 Ohm |
| INCOM Signals (Main INCOM JACK)---ENG |
Head Set OutputLow impedance +10dB at maximum control |
| TALLY (R,G) Signals (for picture monitor) |
Contact closure |
| Ikegami OCP COMMAND Signal (HED) | |
| Ikegami MCP COMMAND Signal (HED) | |
| Data Signal (TX Data) | Separate RS232C link (p+tetc) 9600bps |
| Transmission Distance | Triax Cable75m to 750m with φ8.8mm Fujikura 150m to 1500m with φ14.5mm Fujikura |
| Power Requirement | AC Input voltageAC100-120V/220-240V +/-10% 50/60Hz Power consumptionLess than 86VA (with Cam,smallVF,smallLens) Transmission Power Supply VoltageDC270V |
| Ambient Temperature | Triax Camera Adaptor:-20°C ~ +45°C, Base Station:20°C ~ +45°C |
| Ambient Humidity | Triax Camera Adaptor:-25% ~ +85%, Base Station:25% ~ 85% |
| Weight | Triax Camera Adaptor: Approx. 2kg, Base Station:Approx. 6.3kg |
- Personal information is required
- Software
To download these information, personal information is required. Click the right blue button to download. ：Personal information is not required.